4 Step Guitar re-String Plan

how to string guitar

Here is my 4 step Guitar re-String Plan – it’s simple and easy to follow.  Enjoy!


Guitar re-String Step 1: Remove old strings

Start by taking off the old strings. Some find it easy to grab a string winder and unwind the tuners and then coil the old string up. Others do this by hand, while some prefer to cut the strings and then deal with each end differently. Just make sure you get the whole string off the guitar.


Tip #1

If you play a Strat or Tele style, then find a set of small screwdrivers – from any good DIY store (this shouldn’t cost you more than a couple of $s or £s). That way you can either push or pull lost ball ends out and check that each string hole is empty of debris.


So we have removed the old strings. Clear out any left-over string parts and made sure everything is empty.



Guitar re-String Step 2: Clean

Get a cup of warm water and a cloth. Damp the cloth to just moisten it. Start at the head and clean that, making sure all dust, marks and gunk are removed. Then work down the neck and make sure that you get in between the frets and scrub really hard.


Finally you want to polish the body and the hardware. Finger marks never look good, so get them polished and removed.  Ensure the tuners are moving without any problem and if you have a floating bridge, now is the time to test that it is still moves as it should.


Tip #2

Use fret polish cloths to clean your frets. It’s a good way to protect your frets further.



Guitar re-String Step 3: Lubricate and Restring

Using lube is optional, but it will keep the nut working, so you might want to consider that. You’ll want to move the tuners so that they are placed with their opening facing down the neck, so they are in the right spot to accept strings (so you don’t waste time).


Now there are many ways to restring. The kind of guitar you use will influence how you restring. Some prefer low to high or high to low, and others prefer to work their way inwards in pairs, like so: 6 and 1, 5 and 2 and then 4 and 3.


You can either restring straight through (just like it sounds) by going up over the bridge, through the nut and then into the tuner and tighten – then repeat.


Or when you get to the nut; go round the top of the tuner once, before going into it under this first wind. Don’t worry as this first loop will tighten as you start to wind.


Tip #3

Check your nut! Some nuts are self-lubricating, so you don’t have to worry about it!



Guitar re-String Step 4: Stretch – Tune – Snip

Last step in my guitar re-string plan! When you have added all the strings you need to, next you need to bring them up to tune. At this point it’s good to get a really precise tuner. Start with one string, tune it to the correct pitch, then place your finger lightly over the 12th fret and plug the string again (this is called a harmonic). You want to check that this is in tune as well. If it’s not, you need to get your guitar set up by a good local tech.


Next you need to push down on the string from the top of the fretboard. This will cause the string to lose tuning but will get rid of any slackness in the string and help to tighten the string around the tuner. After you have stretched, you will need to retune, and repeat it a few time until it holds its tuning. If you do this now, you’re less likely to have tuning issues in the future.


Then you need to snip off the excess string at the top and either bend what’s left or just leave it short enough to be useful when restringing, but not so long that it’s getting caught in your case.


Tip #4

When stretching the thinner strings, go carefully or you’ll end up breaking them and having to buy a few sets.


Leave a Reply

Allowed tags: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>